USAutomatic 030213 Two Button Transmitter Remote for Sentry Gate Operators, Single, Grey - Sentry 030213

Sentry Automatic Gate Transmitter 030213 (Operating frequency 433 MHz.)

Part Number: 030213

$18.88 each
OR

Details

USAutomatic 030213 Two Button Transmitter Remote for Sentry Gate Operators, Single, Grey - Sentry 030213

The USAutomatic 030213 Two Button Transmitter Remote works with all Sentry gate openers and is easy to program dip switch. The remote operates up to 300 feet, has an operating frequency of 433.92 MHZ, comes with a visor mount, and includes (1) A23 12 Volt battery. This remote transmitter allows for remote operation of your gate. The first button can be used to control your gate, and the second button can be used for additional customization of your gate system.

Features

  • Operating Frequency: 433 MHz
  • 2 year limited warranty
  • Operates gates or garages
  • Typically operates up to 300 feet

Transmitter Setup:

  • (It is recommended that the dipswitch code be changed from the default factory setting)
  • 1. Open the battery compartment door and locate the dipswitches.
  • 2. Change the dipswitches to the settings you prefer, record for future reference
  • Transmitter Left Button to Receiver Programming: (standard Open/Stop/Close function)
  • Press and hold the left transmitter button down. Red light on transmitter should be on.
  • On the receiver, push the P1 push-button until the green LD light comes on.
  • Release both buttons. Transmitter left button to receiver programming is complete.

Transmitter Right Button to Receiver Programming:

  • (Hold-Gate-Open) (Only if auto close timer is enabled)
  • The 2-channel receiver allows for programming the P2 relay from momentary mode (default) to latching mode. Transmitter right button can be programmed to hold gate open, over-riding the auto-close feature if activated.
  • Press and hold the right transmitter button down.
  • Red light on transmitter should be on.
  • Press the P2 push-button until the green LD light comes on.
  • Release both buttons. Transmitter right button to receiver programming is complete.

Receiver Programming: Relay P2 programming from momentary to latching mode (to hold gate open)

  • Press the P2 push-button until the green LD light comes on, then release. Green LD light should be steady.
  • While the green LD light is on, push the P1 push-button down and release. Green LD light should be flashing. Latching mode is set.

Verifying Receiver P2 relay is programmed to latching mode:

  • Press the P2 push-button until the green LD light comes on, then release.
  • Green LD light should be flashing. If green LD light is steady, redo the Receiver Programming section above.

Resetting receiver P2 relay to momentary mode:

  • Press the P2 push-button until the green LD light comes on, then release.
  • Green LD light should be flashing.
  • While the LD light is flashing, push the P1 push-button down and release.
  • Green LD light should be steady. Momentary mode is set.

Erasing Single Transmitter from Receiver Memory:

  • The dipswitch settings of the transmitter to be deleted must be known. If known follow the steps below.
  • Set the dipswitches in a transmitter to match the switch settings of the transmitter code to delete.
  • Press and hold the left transmitter button.
  • On the receiver, push the P1 push-button until the green LD light comes on. Then release both.
  • Press and hold the right transmitter button.
  • On the receiver, push the P2 push-button until the green LD light comes on. Then release both.
  • Transmitter is now erased from receiver memory.

Erasing all Transmitters from Receiver Memory:

  • Press the P2 button on the receiver until the green LD light comes on. Then release P2 button.
  • While LD light is on press the P1 and P2 buttons simultaneously and hold until the green LD light begins to blink slowly. It should blink 4 times then all transmitter codes are erased.
SKU 030213
Product Type Transmitter
Buttons 2 Button
Frequency 433 MHz
Alternate Sku 30213
Manufacturer USAutomatic, Inc.