Search Site

LCR 4-Button Transmitter - USAutomatic 030212

Availability: In stock

$16.38
  • Buy 50 for $15.88 each and save 4%
OR

Quick Overview

This 4-button transmitter typically operates up to 300 ft away from your gate or garage. Includes a 2-year warranty.

USAutomatic LCR 4-Button Transmitter

Details

USAutomatic 030212 LCR 4-Button Transmitter

  • Operating Frequency: 433 MHz
  • 2 year limited warranty
  • Operates gates or garages
  • Typically operates up to 300 feet

 

Transmitter Setup:

  • (It is recommended that the dipswitch code be changed from the default factory setting)
  • 1. Open the battery compartment door and locate the dipswitches.
  • 2. Change the dipswitches to the settings you prefer, record for future reference
  • Transmitter Left Button to Receiver Programming: (standard Open/Stop/Close function)
  • Press and hold the left transmitter button down. Red light on transmitter should be on.
  • On the receiver, push the P1 push-button until the green LD light comes on.
  • Release both buttons. Transmitter left button to receiver programming is complete.

 

Transmitter Right Button to Receiver Programming: 

  • (Hold-Gate-Open) (Only if auto close timer is enabled)
  • The 2-channel receiver allows for programming the P2 relay from momentary mode (default) to latching mode. Transmitter right button can be programmed to hold gate open, over-riding the auto-close feature if activated. 
  • Press and hold the right transmitter button down. 
  • Red light on transmitter should be on.
  • Press the P2 push-button until the green LD light comes on.
  • Release both buttons. Transmitter right button to receiver programming is complete.

 

Receiver Programming: Relay P2 programming from momentary to latching mode (to hold gate open)

  • Press the P2 push-button until the green LD light comes on, then release. Green LD light should be steady.
  • While the green LD light is on, push the P1 push-button down and release. Green LD light should be flashing. Latching mode is set.

 

Verifying Receiver P2 relay is programmed to latching mode: 

  • Press the P2 push-button until the green LD light comes on, then release.
  • Green LD light should be flashing. If green LD light is steady, redo the Receiver Programming section above.

 

Resetting receiver P2 relay to momentary mode:

  • Press the P2 push-button until the green LD light comes on, then release.
  • Green LD light should be flashing.
  • While the LD light is flashing, push the P1 push-button down and release.
  • Green LD light should be steady. Momentary mode is set.

 

Erasing Single Transmitter from Receiver Memory:

  • The dipswitch settings of the transmitter to be deleted must be known. If known follow the steps below.
  • Set the dipswitches in a transmitter to match the switch settings of the transmitter code to delete.
  • Press and hold the left transmitter button.
  • On the receiver, push the P1 push-button until the green LD light comes on. Then release both.
  • Press and hold the right transmitter button.
  • On the receiver, push the P2 push-button until the green LD light comes on. Then release both.
  • Transmitter is now erased from receiver memory.

 

Erasing all Transmitters from Receiver Memory:

  • Press the P2 button on the receiver until the green LD light comes on. Then release P2 button.
  • While LD light is on press the P1 and P2 buttons simultaneously and hold until the green LD light begins to blink slowly. It should blink 4 times then all transmitter codes are erased.
Programming Guide

Additional Information

SKU 030212
Manufacturer USAutomatic, Inc.
Alternate Sku 30212